Currently the only beep code indicates that a video error has occurred and the BIOS cannot initialize the video screen to display any additional information. This beep code consists of a single long beep followed by two short beeps. Any other beeps are probably a RAM problem.
2.BIOS ROM checksum error - System halted
The checksum of the BIOS code in the BIOS chip is incorrect, indicating the BIOS code may have become corrupt.
Contact your system dealer to replace the BIOS.
3.CMOS battery failed
CMOS battery is no longer functional. Contact your system dealer for a replacement battery.
4.CMOS checksum error - Defaults loaded
Checksum of CMOS is incorrect, so the system loads the default equipment configuration. A checksum error may indicate that CMOS has become corrupt. This error may have been caused by a weak battery. Check the battery and replace if necessary.
5.CPU at nnnn
Displays the running speed of the CPU.
6.Display switch is set incorrectly.
The display switch on the motherboard can be set to either monochrome or color. This message indicates the switch is set to a different setting than indicated in Setup. Determine which setting is correct, and then either turn off the system and change the jumper, or enter Setup and change the VIDEO selection.
7.Press ESC to skip memory test
The user may press Esc to skip the full memory test.
8.Floppy disk(s) fail
Cannot find or initialize the floppy drive controller or the drive. Make sure the controller is installed correctly. If no floppy drives are installed, be sure the Diskette Drive selection in Setup is set to NONE or AUTO.
9.HARD DISK initializing
Please wait a moment... Some hard drives require extra time to initialize.
10.HARD DISK INSTALL FAILURE
Cannot find or initialize the hard drive controller or the drive. Make sure the controller is installed correctly. If no hard drives are installed, be sure the Hard Drive selection in Setup is set to NONE.
11.Hard disk(s) diagnosis fail
The system may run specific disk diagnostic routines. This message appears if one or more hard disks return an error when the diagnostics run.
12.Keyboard error or no keyboard present
Cannot initialize the keyboard. Make sure the keyboard is attached correctly and no keys are pressed during POST. To purposely configure the system without a keyboard, set the error halt condition in Setup to HALT ON ALL, BUT KEYBOARD. The BIOS then ignores the missing keyboard during POST.
13.Keyboard is locked out - Unlock the key
This message usually indicates that one or more keys have been pressed during the keyboard tests. Be sure no objects are resting on the keyboard.
14.Memory Test :
This message displays during a full memory test, counting down the memory areas being tested.
15.Memory test fail
If POST detects an error during memory testing, additional information appears giving specifics about the type and location of the memory error.
16.Override enabled - Defaults loaded
If the system cannot boot using the current CMOS configuration, the BIOS can override the current configuration is a set of BIOS defaults designed for the most stable, minimal-performance system operations.
17.Press TAB to show POST screen
System OEMs may replace the Award BIOS POST display with their own proprietary display. Including this message in the OEM display permits the operator to switch between the OEM display and the default POST display.
18.Primary master hard disk fail
POST detects an error in the primary master IDE hard drive.
19.Primary slave hard disk fail
POST detects an error in the secondary master IDE hard drive.
20.Resuming from disk, Press TAB to show POST screen
Award offers a save-to-disk feature for notebook computers. This message may appear when the operator re-starts the system after a save-to-disk shut-down. See the Press TAB ... message above for a description of this feature.
21.Secondary master hard disk fail
POST detects an error in the primary slave IDE hard drive.
22.Secondary slave hard disk fail
POST detects an error in the secondary slave IDE hard drive.
|305||본체 전원코드를 꼽으면 부팅이 되는 경우|
|304||윈도우 XP운영체제에서 한글 97실행이 안 되는경우|
|303||윈도우 엑스피 부팅후 종료시 자동으로 안꺼지는 문제|
|302||인터넷에서 그림볼때 엑스박스가 나오는 경우|
|301||자동설치되는 파란색의Cometcurse 제거|
|300||마우스 휠을 이용한 2가지 팁|
|299||마우스 왼쪽버튼을 3번 누르면?|
|298||컴퓨터 체감성능을 높여주는 부품순위|
|296||fscagent.exe 파일에 대한 이해|
|295||윈도우 오류메세지 정리|
|294||일본어 게임을 위한 윈도우 언어세팅|
|293||Windows 작업관리자 기본 프로세스|
|292||응답없는 프로그램 빨리종료 시키기|
|291||L2 Cache 용량 지정하기|
|290||IP 스캐닝 프로그램|
|289||명령 프롬프트 창에서 폴더 이름 자동 채움|
|288||Netstat 간략 설명|
|287||램크기에 따른 디스크 캐쉬 설정|
|286||바탕화면 아이콘 만들기|